Snow Performance Stg 2 Boost Cooler F/I Prog. Water Injection Kit (SS Braided 4AN Fitting) - No Tank
Snow Performance Stg 2 Boost Cooler F/I Prog. Water Injection Kit (SS Braided 4AN Fitting) - No Tank
Snow Performance Stg 2 Boost Cooler F/I Prog. Water Injection Kit (SS Braided 4AN Fitting) - No Tank
Snow Performance Stg 2 Boost Cooler F/I Prog. Water Injection Kit (SS Braided 4AN Fitting) - No Tank

Snow Performance Stg 2 Boost Cooler F/I Prog. Water Injection Kit (SS Braided 4AN Fitting) - No Tank

SNOSNO-210-BRD-T

Regular price USD $962.51 Sale price USD $687.50 Save USD $275.01

/
Shipping calculated at checkout.

Unlock 50-70+HP on your boosted vehicle while decreasing your air temps by up to 100 degrees! Increase your pump gas octane by 25 points and make more power efficiently with a cooler running motor! The Snow Performance Stage 2 Boost Cooler water-methanol injection system is available for all forced induction applications (supercharged/turbocharged). The Stage 2 uses the progressive VC-50 controller (52mm Gauge) that proportionally injects more or less according to boost pressure. Start and full points are adjustable for engagement and delivery curve to match what the engine requires. Proportionally injecting according to boost pressure gives an accurate delivery of water-methanol and allows cooling and performance improvements over a wide range for improved drivability. The Stage 2 introduces the VC-50 Controller (ISO 9001 Manufactured). The VC-50 offers the functionality of a boost gauge and water-methanol controller all in one! Highlighting a 7 color (Blue, White, Red, Yellow, Orange, Purple, Green) OLED screen displaying boost, percentage of injection, low level, secondary nozzle activation, prime button, and 2 fault codes directly on the screen you can tailor the controller to your OEM gauges or mix and match up to two colors. Comes with 4AN fittings and stainless steel braided line to mount pump/tank in engine bay of vehicle. For trunk mount options see Part# SNO-40014-BRD, SNO-40012-BRD.

HPA branded products carry a one year warranty against manufacturer's defects on all major, non-consumable, components.  Damaged caused by incorrect installation, wear and tear, abuse, misuse, racing, collision, foreign particles, etc., will NOT be covered by warranty.

Warranty is offered to original purchaser only and is not transferable.

HPA Motorsports will not be liable for incidental, consequential, indirect, special, or punitive damages of any kind.  HPA’s entire liability shall be limited to replacement or repair of the damaged parts at HPA’s option. 

Labour and freight costs associated with warranty repair or replacement are NOT covered.

To maintain validity of warranty, factory recommended maintenance schedule and manufacturer’s Technical Service Bulletins (TSB’s) must be adhered to and documented.

In addition to the above, the HPA FT/FTX series Turbo packages for VR6 motors have the following conditions:

Components covered by warranty include:

  • Turbochargers
  • Exhaust Manifold
  • Downpipe
  • Catalysts
  • Exhaust System
  • Intake Manifold
  • Silicone Plumbing
  • Intercoolers
  • Fuel Pump
  • Fuel Injectors
  • Brake Calipers
  • Haldex Controller

Components NOT covered by warranty include:

  • Clutch
  • Gearbox
  • Brake Pads & Brake Rotors

Any claims of defect in workmanship must be repaired at HPA Motorsports' facility located in Langley, Canada. Should the damage be determined to be a direct result of the workmanship of HPA Motorsports, labor costs for HPA Motorsports to complete repairs at our own facility will be included in the warranty repair. In certain circumstances, at the sole discretion of HPA Motorsports, permission may be granted for repairs to be completed at an HPA authorized facility at a pre-approved labor rate.

HPA Motorsports will not be liable for incidental, consequential, indirect, special, or punitive damages of any kind. HPA’s entire liability shall be limited to replacement or repair of the damaged parts at HPA’s option.

To maintain validity of warranty, in addition to the factory recommended maintenance schedule, the following services must be adhered to and documented according to the prescribed schedule:

Break In period: engine speed is not to exceed 5500 RPM, and absolutely NO standing starts are to be performed 1000 km / 620 miles
Mass Air Flow meter – Clean 5000 km / 3100 miles
Mass Air Flow meter – Replace 20,000 km / 12,500 miles
Engine Oil (Motul Xcess / 8100 5w40) & Filter – Replace 5000 km / 3100 miles
Haldex Fluid & Filter – Replace 10,000 km / 6000 miles

Any claims of defect in workmanship must be repaired at HPA Motorsports' facility located in Langley, BC Canada.  Should the damage be determined to be a direct result of the workmanship of HPA Motorsports, labor costs for HPA Motorsports to complete repairs at our own facility will be included in the warranty repair. 

For remote customers, in certain circumstances, at the sole discretion of HPA Motorsports, permission may be granted for repairs to be completed at an HPA authorized facility at a pre-approved labor rate.

 

Should you experience any issues with your items, please contact HPA Motorsports for technical assistance using the form below or by calling 604-888-7274 prior to engaging in any repair procedure.  Failure to follow the advice of our technical support staff may cause undue harm that will not be covered by warranty.