DQ381 Stage 2+ DSG Tune (2018 MK7.5 Golf R - 8V S3)
DQ381 Stage 2+ DSG Tune (2018 MK7.5 Golf R - 8V S3)
DQ381 Stage 2+ DSG Tune (2018 MK7.5 Golf R - 8V S3)

DQ381 Stage 2+ DSG Tune (2018 MK7.5 Golf R - 8V S3)

HVA-DSG-2-DQ381

Regular price USD $749.00

/
Shipping calculated at checkout.

HPA DSG Performance software for the 7-speed DQ381 is now available. This is a must for all high power applications and those drivers who demand the most out of their chassis!

An HPA OnePort OBD Flashing device is required to install this tune from home within minutes.

Note, unless you have a 2018 Golf R or are installing at an HPA dealer, you will also require a DSG Read Cable.

HPA's DSG Performance Software for the DQ381 found in the 2018+ Audi 8V S3 / VW MK7.5 golf R is now available! This TCU software upgrade is a must for all high performance applications and those drivers who demand the most out of their chassis. Our Performance software for your DQ381 gearbox includes:

  • End-user programmable using HPA OnePort OBD Flasher

  • Completely Optimized D & Sport Mode Shifting

  • In-Dash Gear Display

  • Progressive Shift Response

  • Selectable Launch Control RPM which changes with throttle position. (User can select 3 RPM values)

  • Shortened Gear Shifts (Paddle and Lever)

  • Increased Clutch Pressures to support higher torque output

  • Increased Time in Manual Mode Before Reverting to D & Sport Mode

  • Torque limit increased (a necessity for Stage 2 power level and above)

  • Smooth and Intuitive Overall DSG Driving Experience

HPA branded products carry a one year warranty against manufacturer's defects on all major, non-consumable, components.  Damaged caused by incorrect installation, wear and tear, abuse, misuse, racing, collision, foreign particles, etc., will NOT be covered by warranty.

Warranty is offered to original purchaser only and is not transferable.

HPA Motorsports will not be liable for incidental, consequential, indirect, special, or punitive damages of any kind.  HPA’s entire liability shall be limited to replacement or repair of the damaged parts at HPA’s option. 

Labour and freight costs associated with warranty repair or replacement are NOT covered.

To maintain validity of warranty, factory recommended maintenance schedule and manufacturer’s Technical Service Bulletins (TSB’s) must be adhered to and documented.

In addition to the above, the HPA FT/FTX series Turbo packages for VR6 motors have the following conditions:

Components covered by warranty include:

  • Turbochargers
  • Exhaust Manifold
  • Downpipe
  • Catalysts
  • Exhaust System
  • Intake Manifold
  • Silicone Plumbing
  • Intercoolers
  • Fuel Pump
  • Fuel Injectors
  • Brake Calipers
  • Haldex Controller

Components NOT covered by warranty include:

  • Clutch
  • Gearbox
  • Brake Pads & Brake Rotors

Any claims of defect in workmanship must be repaired at HPA Motorsports' facility located in Langley, Canada. Should the damage be determined to be a direct result of the workmanship of HPA Motorsports, labor costs for HPA Motorsports to complete repairs at our own facility will be included in the warranty repair. In certain circumstances, at the sole discretion of HPA Motorsports, permission may be granted for repairs to be completed at an HPA authorized facility at a pre-approved labor rate.

HPA Motorsports will not be liable for incidental, consequential, indirect, special, or punitive damages of any kind. HPA’s entire liability shall be limited to replacement or repair of the damaged parts at HPA’s option.

To maintain validity of warranty, in addition to the factory recommended maintenance schedule, the following services must be adhered to and documented according to the prescribed schedule:

Break In period: engine speed is not to exceed 5500 RPM, and absolutely NO standing starts are to be performed 1000 km / 620 miles
Mass Air Flow meter – Clean 5000 km / 3100 miles
Mass Air Flow meter – Replace 20,000 km / 12,500 miles
Engine Oil (Motul Xcess / 8100 5w40) & Filter – Replace 5000 km / 3100 miles
Haldex Fluid & Filter – Replace 10,000 km / 6000 miles

Any claims of defect in workmanship must be repaired at HPA Motorsports' facility located in Langley, BC Canada.  Should the damage be determined to be a direct result of the workmanship of HPA Motorsports, labor costs for HPA Motorsports to complete repairs at our own facility will be included in the warranty repair. 

For remote customers, in certain circumstances, at the sole discretion of HPA Motorsports, permission may be granted for repairs to be completed at an HPA authorized facility at a pre-approved labor rate.

 

Should you experience any issues with your items, please contact HPA Motorsports for technical assistance using the form below or by calling 604-888-7274 prior to engaging in any repair procedure.  Failure to follow the advice of our technical support staff may cause undue harm that will not be covered by warranty.